How to Clean, Maintain and Fix Trekking Poles

⏱️ Estimated reading time: 11 min

Short answerClean poles after muddy or wet walks with warm water and mild soap, open them up to dry at room temperature and store them dry with the locks released. Never oil them. Free stuck sections with a gentle twist, clean slipping ones, check the cord on folding poles and replace worn tips and caps.
Walker crouching beside an outdoor tap on a stone wall, rinsing two trekking poles, with autumn trees and green fells behind
On this page: Overview
    Summarize with AI

    Key Takeaways

    Brush off mud while it is still soft, then wash the shafts, tips and baskets with warm water and a little mild soap. Take the sections apart or fold them out so you can wipe grit from the joints, wipe the grips with a damp cloth, rinse with clean water and let everything dry naturally before you put the poles away.

    Open the lock fully first, then hold the pole either side of the joint and pull with a gentle twisting movement. Grit and dried mud are the usual causes, so a rinse with warm water around the joint often frees it. Never use pliers or a vice, especially on carbon, and do not force a section that will not move.

    A section that slides down under your weight is usually dirty, wet or not locked with enough tension. Take it apart, clean and dry the inside of the joint and the shaft, then set the lock again following the maker’s instructions. If it still slips after cleaning, stop using that pole on steep ground and contact the seller.

    No. Oil, grease and spray lubricants make the inside of a pole slippery, so locks hold less well, and the film catches dust and grit that then wears the joints. Clean, dry metal or carbon is what you want inside a pole. Use water and mild soap for cleaning and nothing else.

    Clean them, dry them thoroughly with the sections apart, then store them in a cool, dry place indoors with the locks released and the tips covered. Avoid a damp shed, a hot loft or the boot of the car. Before your first spring walk, check the cord, locks, tips and grips again.

    Trekking poles do not ask for much. A wet day on the fells, a muddy forest track or a winter walk in snow leaves grit, water and dirt in places you cannot see, and that is what makes sections stick, locks slip and tips wear out early. Ten minutes of care after a walk keeps them working the way they did on day one.

    This guide covers cleaning, drying and storing poles, plus the most common faults and how to fix them. Folding and telescopic poles need slightly different care, so if you are not sure which type you have, our comparison of folding vs telescopic poles explains how each one works. If you are still at the buying stage, our guide on how to choose trekking poles is the place to start.

    Common pole problems and quick fixes

    Most problems with trekking poles come down to dirt, water or wear. The table shows the usual suspects; the sections below go through each fix step by step.

    Trekking pole problems, likely causes and fixes
    ProblemLikely causeFix
    Section will not slide or come apartGrit, dried mud or water left inside the jointOpen the lock, twist and pull gently, rinse the joint with warm water, dry fully
    Section slips under your weightDirt or moisture in the joint, or too little lock tensionTake apart, clean and dry, then reset the lock as the maker describes
    Folding pole will not lock straightGrit in the joints or a slack internal cordClean each joint, check the cord for fraying or stretch
    Tip skids on rock or tarmacWorn tip or worn walking capReplace the tip or the cap
    Grips feel slippery or grubbySweat, sun cream and dirt on the surfaceWipe with a damp cloth and mild soap, dry naturally
    Rattle or creak in a sectionGrit, a loose lock or damage to the shaftClean and check; if a shaft is cracked or bent, stop using it

    How to clean trekking poles after a walk

    Cleaning is not only about your kit. Scottish Forestry’s Keep it Clean advice points out that spores of harmful tree diseases can live for a long time and travel in mud and leaf litter, and asks walkers to remove soil from their equipment between visits. If you have used your poles to cross a river or a boggy burn, the GB Non-native Species Secretariat’s Check Clean Dry campaign asks you to check, clean and dry kit before you use it somewhere else.

    1. Brush off loose mud outdoors, on a hard surface, before it dries on.
    2. Open the poles up. Release the locks and pull telescopic sections out, or unfold folding poles, so you can reach every joint.
    3. Wash with warm water and mild soap. Use a soft cloth or sponge on the shafts and an old toothbrush around tips, baskets and joints.
    4. Rinse with clean water, especially after a beach walk or salted winter roads.
    5. Wipe the grips with a damp cloth and a little soap. Cork and EVA foam both prefer gentle cleaning to scrubbing; our guide to cork vs foam grips explains how each material behaves.

    Skip solvents, abrasive pads and the dishwasher. They can damage grips, straps and the finish on the shafts.

    Drying and storing your poles

    Water left inside a closed pole is the main cause of stuck sections. After a wet walk, open the poles up and let them dry with the sections apart or extended, at room temperature. Do not put them on a radiator or next to a stove: direct heat can deform foam grips and dry out cork. After a day in snow, let them thaw and drain before you pack them away; our guide to using poles in snow covers winter use in more detail.

    For storage, keep the poles clean, dry and indoors, with the locks released so they are not under tension for months. Cover the tips so they do not damage anything else, and keep them away from a damp shed or a hot car boot. The same applies when you travel: dry poles before they go into a bag, and if you are taking them on a trip by air, our guide to flying with walking poles explains how to pack them.

    Telescopic poles: locks, stuck and slipping sections

    Telescopic poles slide one section inside another and use a lock to hold the length. Lock designs vary between makers, so always follow the instructions that came with your poles. The basic care is the same for all of them, including the telescopic Alpine Explorer, an aluminium pole that adjusts from 95 to 135 cm.

    • Stuck section: open the lock fully, hold the pole either side of the joint and pull with a slow twist. If it still does not move, run warm water over the joint, wait a minute and try again. Do not use pliers or a vice.
    • Slipping section: take it apart, wipe the inside of the joint and the shaft clean and dry, then set the length and lock it again. Test it with your weight before you set off.
    • Never extend past the stop mark printed on the shaft. Too little overlap puts the joint under more strain.
    • No oil or grease. Lubricant makes the lock hold less well and collects grit.

    Folding poles: the internal cord and joints

    Folding poles are held together by an internal cord that pulls the sections into line. Keep each joint free of grit, so the sections seat fully when you assemble the pole. Every few walks, unfold the pole and look at the cord where it is visible between the sections: it should be taut, not frayed or stretched. If a folding pole will not lock straight after cleaning, or the cord looks damaged, stop using it and contact the seller rather than trying to open the pole.

    When you fold the poles away, do not force the sections or bend the cord sharply. Fold them the same way each time and secure them with their strap or a band.

    Tips, walking caps and baskets

    Tips wear down over time, especially on rock and tarmac. Check them before every big walk: a rounded tip skids more easily on hard ground. Rubber caps wear too, and the Ramblers’ walking poles guide notes that rubber bungs muffle tapping and give better purchase on hard surfaces, so replace a cap once it is split or worn smooth. Rinse grit out of baskets and the snow plate on the folding models after use. Our guide to replacing tips and caps explains which tip or basket to use where.

    Check carbon and aluminium shafts for damage

    A quick look along each shaft after a rough day is worth the minute it takes. The two materials show damage differently, as our guide to carbon vs aluminium poles explains.

    • Aluminium: look for dents and bends. A bent section will not slide or lock properly, and straightening it by hand can weaken it further.
    • Carbon: look for cracks, deep scratches and splintered fibres, particularly after a pole has been caught between rocks or trodden on.

    If you find a crack, a bend or splintering, do not use that pole until the section has been replaced.

    A quick check before every big walk

    • Sections slide or unfold smoothly and lock firmly under your weight.
    • On folding poles, the cord is taut and every joint sits fully home.
    • Tips are not worn round; caps are not split.
    • Grips and straps are clean and intact.
    • No cracks, bends or splinters on any shaft.

    Look after them like this and your poles will feel steady and familiar on every walk, from a wet evening loop to a long day on the hills.

    2 thoughts on “How to Clean, Maintain and Fix Trekking Poles”

    1. Pingback: Carbon vs Aluminium Walking Poles: Which Is Better? | BOLLSEN

    2. Pingback: Cork vs EVA Foam Walking Pole Grips Compared | BOLLSEN

    Comments are closed.